Будь ласка, використовуйте цей ідентифікатор, щоб цитувати або посилатися на цей матеріал: http://repository.pdmu.edu.ua/handle/123456789/16424
Назва: Вплив різних методів дезінфекції на розмірну точність відбиткових А-силіконових матеріалів
Інші назви: Влияние различных методов дезинфекции на размерную точность оттискных А-силиконовых материалов
The influence of different methods of dezinfection on the detailed quality of A-silicon impression materials
Автори: Янішен, І. В.
Герман, С. А.
Ярина, І. М.
Янишен, И. В.
Герман, С. А.
Ярина, И. Н.
Yanishen, I. V.
German, S. A.
Yarina, I. M.
Дата публікації: 2018
Видавець: Полтавський державний медичний університет
Бібліографічний опис: Янішен І. В. Вплив різних методів дезінфекції на розмірну точність відбиткових А-силіконових матеріалів / І. В. Янішен, С. А. Герман, І. М. Ярина // Вісник проблем біології і медицини. – 2018. – Вип. 2 (144). – С. 285–288.
Короткий огляд (реферат): Метою дослідження було провести порівняльну оцінку впливу експозиції дезінфікуючих засобів на розмірну точність відбиткових А-силіконових матеріалів в порівнянні з металевою майстер моделлю. Отримані дані свідчать про те що, в цілому методи дезінфекції А-силіконових відбиткових матеріалів не значно впливали на відносну розмірну точність гіпсових моделей, в межах 0,03-0,066%, що відрізняється від контрольної групи з відсутністю етапу дезінфекції відбитків менш ніж на 0,04%. Дослідження показало, що дезінфекція не робить істотного впливу на розміри А-силіконового відбиткових матеріалів і отриманих по ним гіпсовим моделям. Перевищення тривалості дезінфекції впливає на якість відбитків і точність виготовлених незнімних конструкцій протезів.
Целью исследования было провести сравнительную оценку влияния экспозиции дезинфицирую- щих средств на размерную точность оттискных А-силиконовых материалов в сравнении с металлической мастер моделью. Полученные данные свидетельствуют о том что, в целом методы дезинфекции А-силиконовых оттискных материалов не значительно влияли на относительную размерную точность гипсовых моделей, в пределах 0,03- 0,066%, что отличается от контрольной группы с отсутствием этапа дезинфекции оттисков менее чем на 0,04%. Исследование показало, что дезинфекция не оказывает существенного влияния на размеры А-силиконовых оттискных материалов и полученных по ним гипсовым моделям. Превышение длительности дезинфекции влияет на качество оттисков и точность изготовленных несъемных конструкций протезов.
Silicone imprints are the most common in modern clinical practice. They are comfortable in work, very precise and allow to make high-quality working plaster models. The exact imprint of the tissues of the prosthetic bed is the main requirement for imprint materials. However, silicone materials have different physical and mechanical characteristics under the influence of disinfection. In order to determine the volume changes of the prints due to chemical disinfection, was received 50 prints from the metal master models by A-silicone materials presented in the Ukrainian market, namely: “Stomavid” (JSC “Stoma”, Ukraine), “VPS Hydro” (HS Dental, Germany), “Prestige” (Vannini Dental) Italy. The prints were obtained according to the clinical recommendations presented in the manufacturer’s instructions using standard metal punched spoons. After receipt of the prints were divided into groups depending on the method of decontamination. The prints were immersed in a container in such a way that the thickness of the layer of solution above the surface was at least 1 cm or irrigated with a disinfectant, depending on the manufacturer’s instructions. In group I – the prints were irrigated with a solution of “Aerodizine” within 30 seconds; In group II, the prints were immersed in a concentrated solution of “MD-520” for 5 minutes; Group III – in 10% solution of “Lizofarmin-3000” for 10 minutes; in group IV – 0,25% solution “Surfanius Premium” with an exposure of 15 minutes; in the V group – the control, the prints were not disinfected, 2 hours after the receipt of the specimen cast the plaster model. After disinfection, the prints were washed under running water for 1 minute. The precision was studied using an electron microscope XS-3330 (“MICromed”, North Korea). A comparison of the sizes of a specially manufactured metrical high-precision metal model with corresponding sizes of plaster models, cast on reflections from A-silicone material was carried out. The purpose of the study was to made a comparative assessment of the influence of the exposure of disinfectants on the dimensional accuracy of the impression A-silicone materials in comparison with the metal master model. The obtained data indicate that, in general, methods of disinfection of A-silicone impression materials did not significantly affect the relative dimensional accuracy of gypsum models, in the range 0.03-0.066%, which differs from the control group with no stage of disinfection of impressions by less than 0,04%. The study showed that disinfection does not have a significant effect on the dimensions of A-silicone impression materials and gypsum models obtained from them. Excess duration of disinfection affects the quality of the impressions and the accuracy of the manufactured non-removable prosthesis designs.
Ключові слова: А-силіконовий матеріал
відбиткові матеріали
розмірна точність
дезінфекція
А-силиконовый материал
оттискные материалы
размерная точность
дезинфекция
A-silicone material
impression materials
dimensional accuracy
disinfection
УДК: [616.314-77:678.84]:615.28:53.08
ISSN: 2523-4110
2077-4214
DOI: 10.29254/2077-4214-2018-2-144-285-288
URI: http://repository.pdmu.edu.ua/handle/123456789/16424
Розташовується у зібраннях:Вісник проблем біології і медицини, Випуск 2 (144)

Файли цього матеріалу:
Файл Опис РозмірФормат 
The_influence_of_different_methods.pdf242,9 kBAdobe PDFПереглянути/Відкрити


Усі матеріали в архіві електронних ресурсів захищені авторським правом, всі права збережені.